Marks 4WD Portal Axles, Fitted In Sydney
Solve Offroad is the NSW dealer for Marks 4WD Adaptors Portal Axles. A 6 inch lift under the axle, 35 inch tyres, a GVM upgrade and a stronger driveline, all legal in every state and fitted at our Glendenning workshop. Tell us about your Cruiser and we'll walk you through it.
The Ultimate Lift For A LandCruiser
A conventional lift raises the body and the chassis, then leaves the diffs sitting exactly where they were. Portal axles work differently. The gear housing sits below the axle centre, so the whole axle rides higher and the clearance you gain is real clearance, under the part of the vehicle that actually hangs lowest.
The result is a 6 inch lift under the axle, room for 35 inch tyres, 80mm more track, a 16 percent gear reduction that puts less load back through the driveline, and a GVM upgrade to carry it all legally. Because the lift happens at the axle rather than in the springs, the control arms and panhard rods stay close to flat, so bump steer and body sway stay far better behaved than a suspension lift of the same height.
Solve Offroad is the NSW dealer for Marks 4WD, and we build, fit and set these up in house at Glendenning. Second stage manufacture compliant and legal in all states of Australia.
Why Owners Go Portal
Call (02) 9677 0434-
6 Inch Lift Under The Axle
Enquire150mm of genuine clearance under the diff, not just a higher body. The portal housings carry a 101mm vertical offset and lift the differentials with them.
-
Engineered For 35s
EnquireBuilt to suit 35 inch tyres on 17 or 18 inch wheels, with the correct steering geometry designed in rather than worked around.
-
GVM Upgrade Included
EnquireUp from 3300kg to 3950kg on the 79 Series, or 3780kg on the 76 and 78 Series, so the touring setup goes on legally.
-
80mm Wider Track
Enquire100mm per side at the axle, with the rear track corrected to match the front. Noticeably more stable through ruts and side slopes.
-
16% Driveline Reduction
EnquireThe gear reduction happens at the wheel, so every component from the CV joints back to the engine sees 16 percent less load.
-
Legal In Every State
EnquireSecond stage manufacture compliant and road legal Australia wide. We manage the engineering and compliance side for you.
What You Get
The Standard Portal Axle Kit
Portal axles built onto your own diffs, with front and rear portal axle assemblies carrying the 16 percent reduction. Forged chrome moly heavy duty spindles, air operated free wheeling hubs, and heavy duty one piece swivel housings.
Braking is upgraded throughout: high performance Delios slotted rotors front and rear, high temperature pads, and ADR approved stainless steel braided lines replacing all rubber hoses. A transmission drum hand brake is fitted to the transfer case, and the kit includes breathers for the portals and diff housings, an ARB high output air compressor with mounting bracketry, rubber wheel arch flares and wire retainers for the front wheels, plus the GVM upgrade and second stage manufacture compliance.
Brand New Vehicles
Built On A New Vehicle
On a new vehicle the work goes further. Brand new front and rear axle assemblies, with every housing checked for straightness and straightened if required, then additionally braced, welded and re-checked before assembly.
Housings, swivel housings, struts and portal housings are painted before anything goes together. The diff centre is fitted with ring and pinion ratio changes, a factory diff lock, ARB or EATON if requested, and swivel housings run new king pin bearings and knuckle seals. The front axle is assembled with all new CV joints, axles, gears, shafts, bearings and seals, and an additional king pin bearing sits in a ball joint below the lower king pin.
Options
Optional Extras
Alloy or steel wheels in 17 or 18 inch, and a tyre package to match: 315/70 R17, 35 x 12.5 R17, 305/70 R18 or 35 x 12.5 R18.
We can also supply and fit new springs and shock absorbers as part of the build. The portals and larger tyres add unsprung weight, so good quality shocks matter here more than usual.
How They Actually Drive
Book A Chat With Our Team-
Ground Clearance
With 35s fitted, clearance increases roughly 150mm over standard. At the diff it is equivalent to running 43 inch tyres on a standard live axle.
-
Reduced Bump Steer
No suspension lift is required, so control arms and panhard rods stay close to flat. Softer springs become an option, and caster angle stays unchanged.
-
Articulation & Sway
The wider track improves articulation and reduces body sway, because spring height and sway bars stay standard rather than being extended.
-
Driveline Vibration
With little or no suspension lift, driveline angles stay close to standard, so the shaft vibration common to large lifts is largely avoided.
-
Lubrication & Servicing
Each portal holds around 450ml of fully synthetic oil, checked through a filler plug and drained through a plug in the diff housing. Service every 10,000km.
-
Breather System
Portals run external breather ports, extended and run up to the firewall. We run the diff breathers up to the firewall as well.
Fitment, Weights And Wheels
Vehicles. Marks Portal Axles are designed to suit the VDJ76, VDJ78 and VDJ79, and the GRJ71, GRJ76, GRJ78 and GRJ79.
Weights. Towing capacity is 3500kg and GCM is 6800kg. GVM lifts from 3300kg to 3780kg or 3950kg depending on model. Worth knowing before you plan a van: when the vehicle is loaded to the upgraded GVM, towing capacity reduces to 2850kg or 3020kg respectively.
Wheels and tyres. Portals require a high positive offset rim in the LandCruiser 5 x 150 pattern. We have used ROH, CSA, Dynamic and genuine Toyota, in offsets from +40 to +60 across 17 x 8, 17 x 9 and 18 x 9. A 17 x 8 is limited to 315/70 R17; a 17 x 9 takes 315/70 R17 or 35 x 12.5 R17, and an 18 x 9 takes 305/70 R18 or 35 x 12.5 R18.
Flares and clearance. Track increases 70mm per side at the tyre, so the kit is supplied with the rubber flare and fixing screw kit for the front. For the rear we can supply fabricated guards on cab chassis models. Fitting 35s to a Toyota LandCruiser also requires trimming the rear of the front flare for clearance on turns.
What Our Customers Say
Get Your Build Started-
Blake F.
Professionalism, attention to detail and a customer first attitude from the first phone call to driving away in a fully kitted Next Gen Ranger. They coordinated everything with the dealership, so the whole process was hassle free.
-
Adrian S.
The best and most trustworthy offroad specialist in Sydney. Great impartial advice and fantastic customer service. Still the only place he'd trust his truck to, even after the move put them 45 minutes away.
-
Ethos Performance
Came in to discuss a Troopy build and got straight up, honest and very practical advice. Rates it the best offroad specialist shop he's been to.
-
Kieran W.
Had a long list of mods for his Jeep Wrangler before a lap of Australia. Most shops couldn't help in the timeframe he needed. Solve stepped up and got the build done.
-
Offroad Images
Travels all over the country and needs to be completely confident in the vehicle. Says Nick and the team are absolutely amazing and your vehicle is in great hands.
-
Nik F.
Excellent communication, excellent workmanship and competitive pricing. The team take the time to do the job properly rather than rushing it to make more money.
Who We Are
Solve Offroad is Australian owned and operated, which began through a passion for four wheel driving and offroad racing. And through our passions, we understand the importance of sustaining quality products to make the most out of your vehicle.
We are the NSW dealer for Marks 4WD Adaptors, and a portal build is about as involved as 4WD work gets. Everything is planned, assembled and fitted by our own team at Glendenning, and we'll tell you honestly whether portals are the right answer for how you use the vehicle or whether your money is better spent elsewhere.
We know you love your vehicle, because our staff all love theirs. We go the extra mile, so you can go the extra thousand.
What Happens From Here
Start With Step One-
1. Tell Us About The Vehicle
Model, year, what you've already fitted and how you use it. That tells us whether we're working on your diffs or building onto new axle assemblies.
-
2. We Spec The Kit
Wheel and tyre package, diff centre and ratio, springs and shocks, flares, and the GVM figure that suits what you actually carry.
-
3. Quote And Book In
A clear quote with the compliance work included, then a workshop date. We'll give you an honest lead time rather than an optimistic one.
-
4. Built, Fitted And Complied
Assembled and installed by our own team at Glendenning, second stage manufacture compliant, and backed afterwards.